McGrath RBB56 Wireless Keypad for the McGrath Locks Z Chip - Battery Powered, IP65, Silver
At A Glance
The McGrath RBB56 is a battery-powered wireless keypad and RFID reader designed and supplied specifically as an accessory for the McGrath Locks Z Chip. It communicates with the paired Z Chip via Bluetooth 5.4 BLE and is managed entirely through the McGrath Locks App.
Commonly used for gates, garages and secondary entry points where the Z Chip is mounted internally or out of reach, the RBB56 provides a surface-mounted wireless input point up to 8 to 10 metres from the paired device. Its zinc alloy construction and IP65 rating make it suited to exposed outdoor positions. It is powered by 3 x AAA alkaline batteries with no wiring required.
Usually same day when ordered before 11am AEST (excluding weekends and QLD public holidays).
The RBB56 does not contain a latch, deadbolt, motor or relay - it cannot function as a standalone lock or access controller. It is designed and supplied specifically as a wireless accessory keypad for the McGrath Locks Z Chip and pairs with Z Chip devices only.
It does not pair with McGrath's other smart locks or with smart locks from any other brand. If you already own a different McGrath lock (or a lock from another manufacturer) and want to add a wireless PIN/RFID keypad to it, the RBB56 is not the right product for that job - check with us before ordering. If you need a self-contained keypad that works entirely on its own, with no Z Chip required, see the TGFP43, TGFP70 or RBH52 standalone access control keypads instead.
Key Features
- Wireless external keypad and RFID reader - pairs exclusively with the McGrath Locks Z Chip.
- Communicates via Bluetooth 5.4 BLE with an external BLE antenna.
- Provides PIN code and RFID card/fob access - mirrors the paired Z Chip's user database.
- No wiring required - powered by 3 x AAA alkaline batteries (not included).
- Battery life up to 18 months (based on approximately 10 uses per day).
- Operating range of 8 to 10 metres from the paired Z Chip.
- One keypad can be paired with up to three Z Chip devices simultaneously (requires keypad firmware 7.0.035.260319 or later).
- A single Z Chip can be paired with one keypad only.
- Zinc alloy metal construction, IP65 rated for outdoor installation.
- Managed entirely through the McGrath Locks App.
- Supplied with 2 x RFID fobs.
The RBB56 does not store users, make access decisions, or control any locking hardware on its own. When a PIN or RFID credential is entered at the keypad, the RBB56 sends the request wirelessly via Bluetooth to the paired McGrath Locks Z Chip. The Z Chip validates the credential against its own user database and - if valid - switches its relay to grant access to whatever it is wired to (a gate, garage door, electric strike, or roller door).
All users, credentials, schedules, and access rules are managed in the McGrath Locks App under the paired Z Chip, not the keypad. Adding or revoking a user in the app immediately affects what works at the RBB56. Because it is an accessory to the Z Chip, the RBB56 inherits exactly the same PIN capacity, RFID capacity, and access rules as the Z Chip it is paired with.
Access Methods
Fingerprint
Palm Recognition
Face RecognitionFor background on how Bluetooth, RFID and PIN each work in practice, see the Access Methods chapter of our Smart Lock Buyer's Guide.
McGrath Locks App
The RBB56 is managed through the McGrath Locks App, McGrath's customised build on the TTLock platform (also TTHotel). All pairing, credential management, and access control for the RBB56 is performed from within the app under the paired Z Chip's settings - not the keypad directly. The app is available on Apple and Android devices (iOS 7.0 and above, Android 4.3 and above). For day-to-day platform guidance see the TTLock Platform Guide and TTLock Tips and Tricks.
The McGrath Locks App and the underlying TTLock platform are managed, supported and distributed locally in Australia by LSC and Terry's - not left to an overseas app store listing with no local backup.
The RBB56 does not have built-in Wi-Fi. Remote access and management over the internet depends entirely on whether the paired Z Chip is connected to a McGrath gateway (G3, G4 or G5). If the Z Chip is gateway-connected, remote management flows through that gateway to the Z Chip and, through it, to the RBB56's own credentials. For guidance on available McGrath gateway options and selection, see the Gateway Comparison chapter or the G2 vs G3 vs G4 vs G5 Gateways comparison.
Battery, Power & Consumption
- Powered by 3 x AAA alkaline batteries (not included).
- Battery voltage: 4.5 volt.
- Standby current: less than 20mA.
- Working current: less than 80mA.
- Battery life up to 18 months (based on approximately 10 uses per day).
- Low battery alert displayed within the McGrath Locks App.
- Terry's recommends Duracell batteries for consistent performance.
Environment & Construction
- IP65 rated for outdoor installation.
- Zinc alloy metal construction with raised physical button keypad.
- Operating temperature: -20C to +50C.
- Operating humidity: 0% to 85% RH.
For background on IP ratings and what they mean in Australian conditions, see the Australian Standards chapter.
What's in the Box
- RBB56 wireless keypad
- 2 x RFID access fobs
- Mounting screws and fixings
- User guide
Batteries (3 x AAA) and the McGrath Locks Z Chip are not included - see above.
Suitable Uses
- External keypad input for a McGrath Locks Z Chip located on the internal face of a gate, garage or entry point.
- Secondary entry point where a wireless keypad is preferable to hardwiring a second access controller.
- Outdoor installations where the paired Z Chip is positioned out of reach or out of sight.
- Battery-operated setups where no 12 volt supply is available at the keypad mounting position.
The RBB56 cannot function as a standalone door controller and cannot be paired with anything other than a McGrath Locks Z Chip. If you need a hardwired standalone access-control keypad instead, see the TGFP43, TGFP70, or RBH52.
Available Finish Options
Silver
(This Product)
STK MLKPRBB56SL
Finish selection does not affect functionality, compliance, or performance.
Item Code Family - Access Control Keypad Range
This product (bold row) is the only battery-powered, wireless accessory keypad in the range - the other three rows are self-contained, hardwired standalone controllers that do not need a Z Chip.
RBB56 vs RBH52 - Which Should You Choose?
The RBB56 and the RBH52 are easy to confuse because they look similar and sit in the same part of the range, but they solve different problems. The RBB56 is a wireless accessory that only ever works through a paired McGrath Locks Z Chip. The RBH52 is a complete, self-contained 12 volt controller with its own built-in relay, so it interfaces far more widely - it wires directly to almost any compatible electric strike, magnetic lock, gate motor, garage door or automated door, with no Z Chip or other McGrath device required at all.
Choose the RBB56 only if you already have, or are also buying, a McGrath Locks Z Chip - it has no function without one. Choose the RBH52 if you want one self-contained device that interfaces with a much wider range of hardware on its own - electric strikes, magnetic locks, gate motors, garage doors and automated doors - without needing any other McGrath product.
Compatible RFID Credentials
The RBB56 reads 13.56MHz MIFARE credentials and is supplied with 2 RFID fobs. Additional McGrath MIFARE 1K credentials that work on this reader include:
Full Specifications
Frequently Asked Questions
No. The RBB56 is designed exclusively as a wireless accessory keypad for the McGrath Locks Z Chip. It does not pair with McGrath's other smart locks or with smart locks from any other brand. If you need a keypad for a different lock, check with us before ordering, or see the TGFP43, TGFP70 or RBH52 standalone keypads instead.
No. The RBB56 is a wireless keypad accessory, not a standalone access controller. It must be paired with a McGrath Locks Z Chip, which does all the user validation and switches its own relay to control whatever it is wired to.
One RBB56 can be paired with up to three Z Chip devices simultaneously, provided the keypad is running firmware 7.0.035.260319 or later. Each individual Z Chip can only accept one wireless keypad. If you try to add the keypad to a fourth Z Chip, you will need to remove it from one of the existing three first.
Battery life is rated at up to 18 months based on approximately 10 uses per day. The McGrath Locks App will alert you when the battery is running low. Terry's recommends Duracell batteries for consistent performance. Batteries are not included.
The RBB56 itself has no Wi-Fi. Remote management is possible only if the paired Z Chip is connected to a compatible McGrath gateway. If the Z Chip is gateway-connected, management flows through the gateway to the Z Chip and its paired keypad. For gateway options, see the Gateway Comparison chapter or the G2 vs G3 vs G4 vs G5 comparison.
McGrath smart locks and accessories are backed by long-established Australian industry partners and supported locally by Terry's. To understand why we back the McGrath range long-term, read Why Terry's, LSC and McGrath Locks Give Long-Term Confidence, or see the McGrath section of our Brand Profiles chapter.
Additional Information
- Buy it alongside, or to add to, a Z Chip - not as a general McGrath keypad. The RBB56 only makes sense as a purchase when you have (or are also buying) a McGrath Locks Z Chip. It is not a general-purpose McGrath accessory and will not add wireless PIN/RFID access to any other McGrath lock you may already own.
- Firmware matters for multi-device pairing. Pairing one keypad to more than one Z Chip (up to three) requires the keypad to be running firmware 7.0.035.260319 or later. If your keypad predates this, check the McGrath Locks App for a firmware update before attempting to add it to a second or third Z Chip.
- Fills a specific gap in the range. It is the only product in the McGrath keypad range that runs on batteries and requires no wiring at the mounting position - the right choice when a Z Chip is installed on the internal face of a gate, garage door or entry point and 12 volt cabling to an external keypad position is impractical.
- Hardwired standalone alternatives exist. The TGFP43, TGFP70 and RBH52 are self-contained alternatives when you want a single device that controls the lock and provides keypad access in one unit, with no Z Chip needed. For buyers comparing McGrath with other platform-based smart lock ecosystems, see the App Platforms chapter and Which App Platform Is Right for You.
Warranty
12-month warranty against defects in materials and workmanship (24-month on ALBION, ASCOT, WINDSOR, ULTRA SECUA, HAMILTON, BARDON and STAFFORD models - not applicable to this product). McGrath Locks will repair, replace, or refund at their discretion. Proof of purchase required for all claims.
Download PDF Resources
Full technical specifications - hardware, enrolment and verification, power and environmental ratings.
Configuration mode, adding and removing the keypad from a lock, and troubleshooting.
McGrath RBB56 - FAQ, Setup and Owner's Guide
Everything a buyer or installer needs to know about the RBB56 wireless keypad, in more depth than the main product description. See also our Smart Lock App Platforms chapter and the TTLock Platform Guide for the wider ecosystem this keypad belongs to.
Compatibility and Pairing
No - and this is the single most important thing to know before buying it. The RBB56 is built and sold as a dedicated accessory for the McGrath Locks Z Chip only. It has been tested against McGrath's other smart locks and against smart locks from other manufacturers, and it does not pair with any of them. If a listing or a generic McGrath support document implies broader compatibility, treat this page and the Z Chip pairing requirement as the accurate scope.
No. Only the McGrath Locks Z Chip can be paired with the RBB56. If you have a different McGrath lock and want wireless PIN/RFID entry, speak to us before ordering - a standalone keypad such as the RBH52 may suit your situation better, since it works on its own rather than pairing to another device.
One RBB56 can be enrolled to up to three separate Z Chip devices at once, provided the keypad's firmware is 7.0.035.260319 or later. Going the other way, each individual Z Chip only ever accepts one wireless keypad at a time - it is not possible to run two RBB56 keypads on the same Z Chip. If you try to add a fourth Z Chip to an already-full keypad, remove it from one of the existing three in the app first.
Access & Credentials
PIN codes and 13.56MHz MIFARE RFID credentials (cards, fobs, stickers or wristbands). Credentials are always added through the paired Z Chip's own settings in the McGrath Locks App - never directly on the keypad. Once added there, the same PIN or card works at the RBB56 immediately, because the keypad simply mirrors whatever the Z Chip already has enrolled. See our Access Methods chapter for how PIN and RFID access generally work across smart locks.
McGrath rates the RBB56 at 8 to 10 metres from the paired Z Chip. That is a line-of-sight figure - masonry walls, metal gates and dense foliage will reduce it in practice. For a garage or gate installation, keep the Z Chip and keypad on the same side of any thick wall where possible, or budget for a shorter practical range.
Yes. The RBB56 ships with 2 RFID fobs, and any additional McGrath MIFARE 1K credential works on the same reader - see the Compatible RFID Credentials table on the main product page for the card, fob, sticker and wristband options. All are added to the Z Chip's own credential list in the app, not the keypad.
Power & Batteries
3 x AAA alkaline batteries, not included, running at 4.5V. McGrath rates battery life at up to 18 months based on around 10 uses a day - heavier daily use (a busy shared gate, for example) will shorten that. Standby draw is under 20mA and working current under 80mA. The McGrath Locks App shows a low battery warning under the paired Z Chip when it is time to change them; Terry's recommends quality alkaline batteries such as Duracell for consistent performance.
Yes, within its rating. The RBB56 is IP65 rated and built from zinc alloy, and is specified to operate from -20C to +50C at up to 85% relative humidity - a genuinely outdoor-capable keypad, not one that merely tolerates brief exposure. Mount it clear of direct sprinkler spray and standing water for the longest service life.
Remote Access & Gateway
No - the keypad and its paired Z Chip talk to each other over Bluetooth and work perfectly well with no internet connection at all, as long as you are within Bluetooth range with the app open. A gateway (G3, G4 or G5) becomes necessary only if you want to add or manage users, or check activity, from outside Bluetooth range - and the gateway attaches to the Z Chip, not the RBB56 itself. See the Gateway Comparison chapter or the G2 vs G3 vs G4 vs G5 comparison to choose one.
Installation, Configuration & Troubleshooting
If the keypad has never been added to a Z Chip, install the batteries and either press any button or enter *529# to enter configuration mode. If it is already paired to a Z Chip and not yet at its three-device limit, enter *529# followed by the six-digit administrator password of any lock it is currently paired with, then #.
To add: put the keypad into configuration mode, open the McGrath Locks App and select the Z Chip, then go to Settings > Wireless Keypad > Add Wireless Keypad and follow the prompts. To remove: put the keypad into configuration mode, open the app and select the Z Chip the keypad is paired with, go to Settings > Wireless Keypad, then swipe left on the keypad entry (or long-press it) and tap Delete, following the in-app prompts to finish.
This usually means the keypad is still registered to a previous Z Chip and has reached a limit, or the two devices are mid-handshake. Remove the keypad from its existing pairing first, confirm it is genuinely in configuration mode, then try adding it to the new Z Chip again.
Suitability & Alternatives
Adding a battery-powered, no-wiring-required PIN/RFID input point to a Z Chip that is mounted internally or out of reach - typically a gate, garage door or secondary entry point where running 12 volt cable to the outside face is impractical.
If you want a single device that provides both the lock/relay function and keypad access without pairing to anything else, choose a standalone controller instead - the TGFP43 (slimline, fingerprint), TGFP70 (built-in Wi-Fi, large user capacity) or RBH52 (built-in Wi-Fi with external antenna) are all hardwired, self-contained options. Compare them in the Item Code Family table above.
Related Products, Guides and Chapters
McGrath Locks Z Chip | TGFP43 Standalone Keypad | TGFP70 Standalone Keypad | RBH52 Standalone Keypad | ML-A02 Door Controller | McGrath G3 Gateway | McGrath G4 Gateway | McGrath G5 Gateway | McGrath RFID Card | McGrath RFID Fob | Ch 03 - Access Methods | Ch 08 - Gateway Comparison | Ch 10 - Brand Profiles (McGrath) | Ch 11 - Australian Standards | Ch 14 - TTLock Platform Guide | Ch 15 - Smart Lock App Platforms | TTLock Tips and Tricks | Which App Platform Is Right for You | Terry's, LSC and McGrath - Long-Term Confidence
What's In The Box - McGrath RBB56
- RBB56 wireless keypad
- 2 x RFID access fobs
- Mounting screws and fixings
- User guide
McGrath RBB56 - Product Brochure
McGrath RBB56 - User Guide
PDF Files - McGrath RBB56
Full technical specifications - hardware, enrolment and verification, power and environmental ratings.
Configuration mode, adding and removing the keypad from a lock, and troubleshooting.
McGrath Locks Warranty
Warranty Summary
How to Make a Claim
- Contact Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries (the place of purchase) within the applicable warranty period.
- Supply your proof of original purchase - a receipt or tax invoice is required.
- Provide a clear description of the fault and your contact details.
- You may be asked to return the product for assessment before a remedy is determined.
- McGrath Locks will, at their discretion, repair the product, replace it with the same or an equivalent model, or provide a refund of the purchase price.
Exclusions
This warranty does not cover:
- Normal wear and tear
- Products that have been disassembled
- Damage caused by improper handling, incorrect installation, misuse, abuse, neglect, modification, or accident
- Installation by unlicensed persons (including non-licensed locksmiths or technicians)
- Products not used in accordance with the supplied instructions
- Cosmetic damage that does not affect functionality
- Labour or installation costs related to the removal or reinstallation of products
- Exposure to conditions outside normal environmental use
- Work completed before warranty approval
- Damage caused by battery leakage, battery failure, or force majeure
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if they fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is provided in addition to your rights and remedies under the Australian Consumer Law.
Confused? Overwhelmed? We get it.
Choosing the right smart lock can be genuinely tricky - door types, backsets, app platforms, compatibility with your existing hardware... there is a lot to consider. We have decades of experience fitting locks of all types, including smart locks, and we are happy to help.
Our expert recommendation service is free. Upload a few photos of your door and describe what you need, and one of our qualified locksmiths will give you a personalised recommendation.
Get Your Free Recommendation →How it works - three easy steps:
1. Upload photos
A few clear shots of your door, lock and frame - inside and out.
2. We assess
Our locksmith reviews your setup and requirements - door type, weather exposure, how you want to use it.
3. You get a recommendation
A personalised recommendation tailored to your door, budget and needs. No pressure, no upsell.
Also useful while you are deciding:
